
                ACCTON TECHNOLOGY CORPORATION
        EN1203, EN1207 Series PCI FAST ETHERNET ADAPTER
             SCO UNIX STREAM DRIVER INSTALLATION

      Copyright 1995-1998 ACCTON Technology Corporation
                      All rights reserved.


Your Driver Diskette should contain the following files in the subdirectory
\SCO:
--------------------------------------------------------------
Files           Contents
--------------------------------------------------------------
ReadMe.TXT      Text file about driver installation for the UNIX Server
UNIXDRVR.tar    PCI ethernet device drivers packaged for UNIX (in tar format)
--------------------------------------------------------------

Introduction
-------------
    This is PCI Ethernet Adapter EN1203/EN1207(TX/B-TX/C-TX) SCO Unix LLI driver R2.1.1.
    It is a custom installable LLI driver, configured using netconfig.
    The LLI driver requires the following software:
    - EN1203/EN1207(TX/B-TX/C-TX) ODT 2.0 or higher version, or SCO Unix r3.2v2
      or higher version (Unix SCO5 excluded).

Installation Procedure
----------------------
1. Prepare a formatted diskette on any DOS machine.  For example, type:

    C>format a:

Note: Make sure your diskette is free from bad sectors.
      Verify this using the DOS SCANDISK or CHKDSK command.

2. Now login to UNIX system as supervisor (root).

    (Note: Make sure that the current directory is "/"
     using UNIX command - pwd.)

   Please follow the following steps to uncompress the package file:

   >  cd /tmp
   >  mkdir tmp
   >  cd tmp    (then inserting the Package Diskette)
   >  doscp a:unixdrvr.tar ./unixdrvr.tar
   >  #dd if=unixdrvr.tar of=/dev/rfd0135ds18
       (Note: Use another device file name if you use different floppy drive)

   Now the package installation diskette is ready for installing.

3. The following sections describe the configuration of
    the driver. It is suggested that you should perform
    these instructions in the singler-user environment.

    Run custom utility and select the "Install new package"
    option. It will prompt you to insert "Accton EN1207 Series Fast
    Ethernet LLI driver" Floppy Volume 1.

4. After reading drive A, it will show a message prompting
    you to use "netconfig" to add drivers into your system.

5. Run "netconfig". Add the desired chain. The Accton EN1207 Series
    drivers are called: actn0, actn1, actn2 and actn3.
    Rember the actn0 must be configured first, before any other driver
    is configured.

6. When the chain has been configured, select 'q' from the netconfig menu
   and relink the kernel at the prompt.

7. To active the adapter, you must reboot. When the system
    boots, you should see the following message among the
    other configuration messages:

    %acc0   0xE000-E800     9   -   type=EN1207B-TX/C-TX/Auto addr=00-00-E8-04-98-56

    with the appropriate I/O addresses, IRQ, Adapter-type with its detected
    media-type and the last three octets of its IEEE address.

8. Use the PCI BIOS setup program to configure your PCI Ethernet adapter.

9. If you encounter any problems during installation,
    (i.e., an error message appears on screen) call your dealer for assistance.

Notes:
    1. Full-Duplex support.
    2. On-the-fly autosense support ONLY for the EN1207TX/B-TX/C-TX adapter.
    2. Auto Detecting AUI/BNC/Twisted-Pair connection media.
    3. The driver supports up to maximum 4 boards.
       It is recommended to configure the PCI board(s) following the
       PCI BIOS limitation on you machine.
    4. Device name is actn0, actn1, actn2, actn3

Trademarks
----------

All trademarks or brand names mentioned are properties
of their respective companies.

===End of File===
