Ŀ
	       32-bit PCI (Fast) Ethernet Adapter		
	    NDIS/2 DRIVER FOR LAN SERVER INSTALLATION		


The driver named ETHPCI contain in the directory NDIS conforms to
the Network Driver Interface Specification (NDIS) defined by
Microsoft/3Com.

DOS LAN Requester
=================
1. Insert the IBM LAN Support Program (LSP) Version 1.30 (or 1.31 to 1.36)
   Diskette into your floppy drive (drive A: or B:).

2. Type the following from your DOS prompt  and press <Enter>:

   A:>dxmaid

3. The screen will display the IBM logo. Press <Enter> twice until the
   "Environment Information" appears onscreen.

4. Responds to the screen prompts, specifying the following values for each
   field:

	  Use the <Space Bar> to toggle between choices:
	  Configuration for this computer?	    Yes
	  Use existing configuration information?   Yes
	  Do you have adapter option diskettes?     Yes
	  Are you configuring for two adapters?     No
	  Do you need 802.2 interface support?	    No

	  Type change as needed to drive and directory information below:

	  Source for LSP			   A:\
	  Target for new configuration		   C:\lsp

5. Make sure that the values given above are correct.  Press <Enter> to store
   your choices.

6. Insert the Driver Diskette in your source drive.  Specify the path and press
   <Enter> to proceed.	Examples:
   A:\NDIS\DOS,
   B:\NDIS\DOS

7. Upon pressing <Enter> the necessary drives from the Driver Diskette are
   copied onto you target directory in the hard disk.

8. Follow screen instructions to complete the process. Simply pressing <Enter>
   for each screen display will select the default options.  Press <Enter> three
   times, until you reach the display prompting you to insert the LSP diskette.

9. Insert the LSP diskette as prompted. Press <Enter> to acknowledge completion
   of the action.

10. A screen showing the current configuration detected will be displayed.
    It should show the and 32-bit PCI Bus (Fast) Ethernet Adapter
    the protocols already selected (i.e., "IBM IEEE 802.2" and
    "IBM OS/2 NETBIOS").

11. Press <F4> to save the new configuration. This completes the LSP
    installation.

   ************************************************************
   *	NOTE:						      *
   *							      *
   *	You should have defined in your CONFIG.SYS the	      *
   *	minimum of 20 files, i.e. FILES=20, to run the	      *
   *	software properly. Change the FILES line using	      *
   *	the text editor if needed.			      *
   *							      *
   *	If installing LSP for the first time, you should      *
   *	complete the installation by typing install and       *
   *	following the further instructions on screen.	      *
   ************************************************************

12. Use a text editor to edit the CONFIG.SYS file.  Specify at least 20 file
    in the FILES= line. Modify it to the following:

	FILES=20

13. Save the configuration and reset your computer.

14. Insert the DOS LAN Requester Install Diskette 1 into your floppy drive.

15. Type the following and press <Enter>:
	INSTALL    <Enter>

16. The IBM logo will again appear on the screen.  Press <Enter> to move on
    to the next screen.

17. Follow screen instructions, pressing <Enter> to move from screen-to-screen
    until you are prompted to indicate the pathname of the DOS LAN Requester
    directory.

	TIP: After the IBM logo appears on the screen,
	     press <Enter> twice to reach this screen.

18. Specify the pathname for the DOS LAN Requester directory (C:\DOSLAN is the
    default).  Then press <Enter> to continue.

19. The program will ask you for the services that you require.

20. Highlight the appropriate option. Select either "Send messages" or
    "Send, View, Edit, and Log message" option.

	TIP: Normally, second option "Send, View, Edit
	     and Log message" is selected.

21. Specify the PC's ID and domain ID.  The domain ID is the domain server ID;
    it should be the same for all workstations of the network.

22. Follow screen prompts to complete the installation.



OS/2 LAN Server 3.0
===================
 1. Copy ETHPCI.OS2 and ETH_32O.NIF files from your Driver diskette
    (A:\NDIS\OS2) to C:\IBMCOM\MACS.

 2. Click the OS/2 LAN Service icon.

 3. Select "Installation and configuration." The IBM logo should
    appear onscreen.

 4. Click <OK>.

 5. Select <Advance> and press <Enter>.

 6. Select "Install or Configuration this Workstation."

 7. Select server type, adding a server or domain controller.
   The "install or remove" selections should appear.

 8. Select "Configure a component."

 9. Click the "Configure" button.

10. Select "Configure workstation."

11. Select "32-bit PCI Bus (Fast) Ethernet Adapter"
    when prompted to identify you Network Adapter, Then click
    the <Add> button.

12. Select "802.2" from the list and click the <Add> button.

13. Select IBM NETBIOS from the list and click the <Add> button.

14. Select <OK> to confirm all selections.

15. Follow screen instructions to complete the process, selecting <OK> to
    accept default selections.

16. Continue pressing <OK> until your screen prompts you to backup old
    CONFIG.SYS and AUTOEXEC.BAT and create a new CONFIG.SYS and AUTOEXEC.BAT.
    Also select <OK> to confirm this.

17. Installation is complete now. Reset your PC by turning it off and on.



OS/2 LAN Server 4.0
===================
 1. In OS2 desktop, click the MPTS(Multi-Protocol Transport Service)
    icon.  The IBM logo should appear on screen.

 2. Click the <OK> button.

 3. Click the <Configure> button.

 4. Select the "LAN adapters and protocols" item, then click <Configure> button.

 5. Click <Other adapters...> button.

 6. Insert Driver Diskette 1 into a specified drive (A: or B:), then enter
    the driver path like

	   A:\NDIS\OS2,   (or B:\NDIS\OS2, etc.)

    and click <OK> button

 7. Select "32-bit PCI Bus (Fast) Ethernet Adapterr" from Network Adapters
    list when prompted to identify you Network Adapter.  Then click the <Add>
    button.

 8. Select "IBM 802.2" from the Protocols list and click the <Add> button.

 9. Select "IBM OS2 NETBIOS" from the Protocols list and click the
    <Add> button

10. Select "IBM Netware Requester Support" from the Protocols list
    and click the <Add> button if you need to logon NETWARE server.

11. Select <OK> to confirm all selections.

12. Click <Close> button in the Configure window.

13. Click <Exit> button in the MPTS window.

14. Click <Exit> button, then your screen will prompts you to backup
    old CONFIG.SYS and AUTOEXEC.BAT and create a new CONFIG.SYS
    and AUTOEXEC.BAT. Also select <OK> to confirm this.

15. Installation is complete now. Reset your PC by turning it off and on.



Multiple adapters installation for IBM LAN SERVER 4.0 on OS/2 system
=====================================================================

For multiple adapters installation, you must do the follows:

    a. configure <LAN Services>
    b. configure <MPTS>


a. Configure <LAN Services>
------------------------------
1. From OS/2 desktop, click <LAN Services>

2. In LAN Services windows, click <OS/2 LAN Services Installation/Configuratin>

3. click <OK> when the IBM logo appears.

4. In "Basic or Advanced Installation/Configuration" dialog box,
   click <Advanced>

5. Select "Install or configure this workstation" in "Installation Tasks"
   dialog box, and click <OK>

6. Select Server Type (like, Domain controller) then click <OK>

7. Select "Configure a component" from "Installation and Configuration" dialog
   box, and click <OK>

8. Select "LAN Services Adapters" from "Configure" dialog box, and click
   <Configure...>

9. Select the LAN adapters to be used by LAN Services (for 2 adapters, select
   Adapter 0, Adapter 1 ) and click <OK>

10.Assign the NETBIOS Resources like Sessions, Commands & Names (you can use
   the default value) and click <OK> for different adapters.

11.Click <OK> from "Configure" dialog box.

12.Select "Apply the changes" and click <OK> from "Installation and
   Configuration" dialog box.

13.Follow screen instructions to complete the installation.

14.Shut down and reboot the machine.


b. Configure <MPTS>
----------------------------------
  If you have more than one adapter, you need to configure each of them
  for different Slots by clicking <Edit> in "Configure" windows.

  ********************************************************************
  *	NOTE!!							     *
  *								     *
  *	Each slot represents an PCI adapter index value for one      *
  *	adapter installed (32-bit PCI LAN adapter in this case)      *
  *	assigned by the PCI-BIOS.  For example, if the 1st slot is   *
  *	assigned slot=16, then the next slot will be assigned	     *
  *	slot=17, the third slot=18 and so forth until the last slot  *
  *								     *
  ********************************************************************


----
All trademarks or brand names mentioned are properties
of their respective companies.

===End of File===
